Skullcandy Indy Evo Not Pairing Together (Fixed)

Skullcandy Indy Evo are great earbuds and I have had never faced any problem. However, a few weeks ago they were not pairing together.

After researching online for hours I have found some ways to troubleshoot this problem.

So, if your Skullcandy Indy Evo not pairing together read the troubleshooting steps written below.

Skullcandy Indy Evo is Not Pairing Together

If your Skullcandy Indy Evo earbuds are not pairing together it is typically a result of software glitches, outdated firmware, mono mode of earbuds and low battery of both earbuds and charging case. To fix this problem you should reset earbuds, update firmware, get them out of solo mode and charge for a while

1. Restart Skullcandy Indy Evo

If your Skullcandy Indy Evo are not pairing together, firstly restart them.

Because it will remove minor software glitches that are mostly responsible for the problem.

Follow the steps below to restart your Skullcandy Indy Evo.

  1. Firstly turn off your Skullcandy Indy Evo by pressing the power button for more than 10 seconds.
  2. Then turn it on by pressing the power button for 10 seconds. 

Now put both Skullcandy Indy Evo buds in the charging case and remove them back to pair with each other. 

2. Reset Skullcandy Indy Evo 

Skullcandy Indy Evo Not Pairing Together

Reset is also the best solution to fix the Skullcandy Indy Evo pairing problem. Because it will remove hardware bugs and glitches.

Moreover, reset will refresh your earbuds and increase their performance. 

Follow the steps below to reset your Skullcandy Indy Evo.

  1. Place your Indy Evo earbuds in the charging case.
  2. Remove your Indy Evo from the device pairing list.
  3. After that, turn off the Bluetooth of your device.
  4. Turn on the right earbud by removing it from the charging case.
  5. Then tap the center of the right Indy Evo bud four times. The bud will automatically turn off, and the LED light will turn red. (means successfully reset, if it doesn’t flash red, then try the same process again until bud’s LED flashes red.) After resetting, place the right bud back in the case.
  6. Now turn on the left earbud by removing it from the case and press its center four times or until it successfully reset. Then place the left bud in the charging case.
  7. Remove both buds from the charging case and let both buds automatically connect together. You will hear a sound that will indicate both buds are now paired. 

If your earbuds are still not pairing after reset, try reset three to four times. 

Here is another method of resetting Skullcandy Indy Evo earbuds.

3. Remove Mono Mode

Skullcandy Indy Evo Not Pairing Together

Skullcandy Indy Evo earbuds have a single bud mode in which you can only use one bud. (You can only use the right bud in the mono mode because it is the primary bud.)

Single bud mode activates when you remove only the right bud from the case, and the left one is still in the charging case.

So, maybe you have done that due to which your earbuds go in the single mode or maybe stuck in this mode and not pairing together.

Therefore you should remove your earbuds from this mode.

Here is how you can do that.

To pair both earbuds to each other or deactivate mono mode first, you must put the right bud in the charging case and then close its lid.

Then remove both buds from the charging case; they will pair with each other.

However, reset your Skullcandy Indy Evo if this doesn’t work. 

4. Charge Earbuds and Case

Skullcandy Indy Evo Not Pairing Together

The low battery of Skullcandy Indy Evo earbuds and their case can also create pairing problem in the buds.

Therefore you should fully charge your buds and their charging case.

Both earbuds will take only 1 hour to fully charge from 0% to 100%. Moreover charging case will take 2 hours to charge from 0% level to 100%. Also, make sure you are correctly charging earbuds and charging case.

After completing the charge, try to pair both Indy Evo buds together. 

5. Update Firmware

Skullcandy Indy Evo Not Pairing Together

In rare cases, firmware can cause connection problems between the Skullcandy Indy Evo earbuds.

Therefore you should update your earbud’s firmware.

Follow the steps below to update your Skullcandy Indy Evo firmware.

  1. Download the Skullcandy app.
  2. Connect Skullcandy Indy Evo with phone and app.
  3. Open the app on your phone and an open notification tab.
  4. If an update is available, download the latest one and complete the process.

What to do if the firmware update won’t begin or fails?

Firmware updates won’t begin.

If your Skullcandy Indy Evo firmware is not updating, then ensure you have completed the steps below.

  1. Make sure your Indy Evo earbuds have at least 25% or more battery. If the earbud’s battery is low, then first charge them.
  2. Your phone has a good internet connection. 
  3. Ensure your phone battery is above 30%. If your phone’s battery is less than 30%, then charge it. 
  4. Earbuds should be connected to your phone and the Skullcandy app.

Firmware update fails

The firmware update can fail for any reason, such as lost connection, phone calls, or the Skullcandy app being closed during the update. 

If your Skullcandy Indy Evo earbud’s firmware update fails, follow the steps below.

  1. Place both buds in the charging case and close its lid. After 5 seconds, remove buds from the charging case. Then connect buds with the Skullcandy app and try to update the firmware.
  2. If your Skullcandy Indy Evo firmware update fails again, place both buds in the charging case and close its lid. Force close the app and remove both Indy Evo earbuds from the case. Now try to update their firmware.

Conclusion

It is really frustrating when Skullcandy Indy Evo is not pairing together. Because you can no longer enjoy your favorite music.

But there are some ways to fix this problem:

  • Restart your Skullcandy Indy Evo
  • Reset your Skullcandy Indy Evo
  • Remove from Solo Mode
  • Charge for a while
  • Update firmware

Skullcandy Dime Not Pairing Together

Related FAQs

How to Pair Skullcandy Indy Evo Together?

Follow the below steps to pair both buds together.

  1. Place both buds in the charging case and wait until both LED’s flash red.
  2. Remove buds back from the charging case.
  3. Both earbuds will automatically turn on and start pairing with each other and LED’s on both buds will flash blue while they are pairing to each other.
  4. On successful pairing you will hear a tone and only left earbud will flash red and blue.

How do I Reset my Indy Evo Earbuds?

Here is how you can reset your Skullcandy Indy Evo earbuds.

  1. Place your Indy Evo earbuds in the charging case.
  2. Remove your Indy Evo from the device pairing list.
  3. After that, turn off the Bluetooth of your device.
  4. Turn on the right earbud by removing it from the charging case.
  5. Then tap the center of the right Indy Evo bud four times. The bud will automatically turn off, and the LED light will turn red. (means successfully reset, if it doesn’t flash red, then try the same process again until bud’s LED flashes red.) After resetting, place the right bud back in the case.
  6. Now turn on the left earbud by removing it from the case and press its center four times or until it successfully reset. Then place the left bud in the charging case.
  7. Remove both buds from the charging case and let both buds automatically connect together. You will hear a sound that will indicate both buds are now paired.